So I have a Graco SafeSeat for my baby who is now 12 months old. It is rear facing and goes up to 30 pounds, so we will be using it for a while longer (my baby is around 20 pounds). My problem is that the base is installed in the middle backseat of my 2001 Chevy Prism, which doesn't have LATCH thingies (it has them on the sides, but not in the middle), so it is installed with the seatbelt which is a shoulder belt, and when I pull the belt as tight as it will go, it pulls up on the side of the base because of the shoulder belt. Does that make sense? So the base is crooked in the car, and it has just gotten worse and worse over the months. It doesn't matter if I take it out and reinstall it, because it has started digging a groove into the seat. I am starting to get really worried about the safety of the carseat when it is crooked like this. I don't think they did crash tests with crooked seats.
Has anybody had a problem like this, or know of a solution for straightening out the carseat?
Our car seats did this, too. We took them to the fire station for help. They took one of those noodles for the pool, cut it in half, taped it back together side by side and put it under the car seat at the corner of the seat and the back. Worked like a charm! We did it with two car seats until we got a car that had the latch system. A seat protector might do the same thing. We use them now, but only because we want this vehicle to look nice for a long time, and 3 car seats is pretty hard on the seats. :) If too much of a groove is there, the seat protector will help even it out a bit. GL! It will be easier once you turn the seat around, but the kiddos are safer when turned backwards.
lots of gov't agencies that deal with kids can help with car seats. the department of health should have someone also who will come and install it for you - at least they do here.
The LATCH system usually has a total of 4 latches in the seat. One on each outter side by the doors and then two towards the middle. You can attach the car seat in the middle seat using the two middle latch hooks. You can buy seat protectors that help (but don't entirely eliminate) the groove in the seat.
I agree that you should take it to a firestation or local hospital for a free car seat installation/inspection.
Find your local car safety seat check. I'm in Pueblo and they have them once a month or two. There's a great on August 1st part of a Teddy Bear Clinic at the mall. You can usually call a fire station too and ask how to get it checked. They are trained on how to put them in correctly, make sure your baby fits into it correctly and there have been no recalls on the seat.
Katie D is right. Try keeping the baby seat in the middle and attaching to the latch system in the "outer" seats. I drive a 2003 Toyota Corola, and this works great for us. My husband is in automotive research and development, and he feels totally comfortable with our son's car seat attached this way. Good luck.
Your carseat should have come with an odd plastic or metal device that is specifically for using on a shoulder belt. It holds the piece that would go across your lap, and the piece that would go across your shoulder, together. I can't explain it very well in words. I ditto going to the fire station (or your hospital) and having someone help you install the car seat. If you don't have that piece (or the seat didn't come with it for some reason) they'll be able to help you get the seat put in so you don't have to worry about your child's safety.
in order to make our baby's carseat level properly, my husband used one of those foam pool noodles. he cut it to the width of the car seat and positioned it under one end. with the seat belt pulled tight it worked very well. we tried a rolled up towel before that, but it kept slipping.
Go get a foam pool noodle (cheap, available at Walmart or similar places), cut it into the appropriate lengths, and use the pieces as bolsters under the sagging side. I learned this trick from a lady at my church who did carseat safety inspections for the police department, and it really does work.
Bonnie,
Call your local fire department they should have a certified person to check and install the car seat correctly for free. If you have latch systems on the side you should be able to still use them in the middle. Just attach to the closest one on each side.
This sounds like it is installed wrong and in your car a middle car seat might not work the best...
I would take it to a local fire station or a hospital that has a safe ride program. I know Rose and St Joseph has them... They can look over what you are doing and help you get it right.
I have heard that up to 60% of car seats are installed wrong, so better by safe than sorry.
Someone mentioned using the latch system on the outer two anchors but still keeping the carseat in the middle. That would be the easiest fix, in my opinion. Someone else also mentioned the piece that comes with the carseat that is used to pull the shoulder belt down to the lap belt so it's not doing what you are describing. It attaches like a cinch to the lap and shoulder belt and is usually metal and shaped like a capital "i" with the top and bottom lines. If you have your carseat manual, you can look it up in there. If not, most manufacturer websites have downloadable copies of user manuals that you can try and see what I'm talking about. But both those options would fix the problem while still keeping the carseat in the middle seat.
You've received some good ideas already, but if your fire department doesn't solve all your problems, the next time you're in Salt Lake, come up to Primary Children's Med Center. We have a "Car Seat Safety Squad" that will definitely answer all your questions/problems. Just call first to make sure of their hours (801)662-1000. Hope this helps!
Hey, Bonnie. I recommend you contact a certified carseat technician. My friend, Susan Saito, works for West Metro Fire Diestrict and she would be happy to help you. Go with a pro...they are most up-to-date with regulations and new ideas on how to trouble shoot car seat problems!
I could be wrong, but I believe the reason the latch system is on the sides of the back seat is because that's the safest place for the babies. Is there a reason you don't move the seat to one of the sides?
I don't know if Target still sells them (i think they do). But you need to go buy a "mighty-tight". This is specifically designed for shoulder strap seat-belts and will work perfectly to straighten and tighten the strap for your child's seat.
The safest spot is in the middle of the back seat, FYI.
You can try calling GRACO. Lots of seats I've owned recommend rolling up a small towel and putting it under the base to level it out correctly. They generally mean front-to-back leveling, but maybe it would work for side-to-side, too.
Another option is to take it to a fire station or similar car seat check place and ask their advice. They may say that you need to move it to a side seat.
BTW, thanks for caring about this and trying to find a solution. I know a LOT of people who just wing it and don't care. I've heard of car seats tipping over on curves, and seen the seat belt as LOOSE as possible instead of as TIGHT as possible. I don't how they could have read the instructions!
You can make an appointment (as soon as possible!) with your local fire or police department--they will ensure it is in correctly. The sooner, the better--it sounds scary to drive around like that. All the best--good for you for making sure it's safe!
HI there, I'm not sure who it is that decided that the middle of the rear seat is the safest seat in the car. If you have a arm rest that acts as the middle seat back then absolutly your car seat should not be in the middle seat. I strongly suggest moving the carseat to one of the side seats./ i have my daughter ont eh drivers seat she is now 6 and when we were involved in a car crash 1 1/2 yrs ago the firemen told me that they were perfectly buckled in on the sides. Move the car seat is my suggestion.
I don't know if anyone mentioned this but when they do safety inspections they use pieces of swimming noodles under the back part of the base to keep it level. You can get them for a buck at the dollar store and just cut a piece off. Another option is a rolled up towel under the problem spot. I've used both and they work great. YOu just have to play with it to get it in the right spot.